No Hole Stairway Baby Gate Mounting Kit By Safety Innovations features

• Hole-Free – No need to drill into your posts!
• Easy Installation!
• Used by professional childproofers
• Fits posts 2 3/4 to 3 5/8 inches
• Gate Not Included

Safe Beginnings Exclusive! Our deluxe Hole-Free Gate Mounting Kit lets you install safety gates to newel posts without drilling into them. Our kit works with posts that are 2 3/4″ to 3 5/8″ wide. Each kit comes with mounting wood and a hardware set to mount one side of a gate. Not for use with pressure gates. GATES ARE SOLD SEPARATELY. If your post is round at the bottom and top please contact us and we will ship you a second set of round adapters free of charge.

Q:Does this work with a specific gate (presumably from the same company) or can I use my old gates? Thanks
A:

It’s a pretty generic setup. It should work with any type of gate that you screw into the wall. The product is basically a piece of wood you screw into the plastic clamps, then you screw your gate into the wood.

Q:Any chance this will work for an iron railing?
A:

There are two components; an outer square and an inner circle so it depends on the diameter of the iron…if it’s similar to a wood post then it would work….if the diameter of the iron is much smaller it might make it too loose

Q:what is you only have ONE baluster? Does this attach to the WALL?
A:

One side attaches to the wall, the other to the banister.

Q:Can someone provide the dimensions? my banister poles are 42 inches apart and 37 inches high. WIll this fit? thanks
A:

This is an adjustment for gates to attach to a banister not an actual gate. This provides stabilization. It fits Fits posts 2 3/4 to 3 5/8 inches which would be the width of a single post.

Q:Will this allow me to install a pressure mounted gate if the other side is a wall?
A:

Yes. Both sides are pressure mounted

Q:some reviews say you must drill a hole in your banister for this to work, others say no. Please, which is it?
A:

We did not have to drill a hole. It’s been up for a year and we’ve had no problems but I won’t really know how well it protected the banister until we take it off which will be quite a few more years I hope.

Q:if you have two balusters do you need two kits (ie: 4 brackets two round, two square?
A:

Yes you will

Q:Will it work with an extra tall gate 32″?
A:

It probably would. The product comes with a long 1″ x 2″ strip that that can be cut down to the size you need. Unfortunately, mine have already been cut so I don’t remember how long the strip was to begin with. I would think if the piece wasn’t long enough, you could probably purchase a longer one at a lumber store.

Q:We have a square post (both top and bottom) and the wall on the other side of the steps. Will this work on a 3.5″ by 3.5″ post (top and bottom)?
A:

Yes

Q:Will this work with the Dreambaby retractable gate?
A:

I’m not sure if it will work with that gate or not. We have an evenflo gate that it work very well with

Q:I can’t find measurements, does anybody know how tall the piece of wood is? I’m worried it won’t fit under the hand-rail on our banister.
A:
I believe it was 36″. However it didn’t fit under my hand rail so I cut it down to size to fit. Hope this helps.

Q:Does this work with the Kidco Safeway Safety Gate?
A:
Yes, it worked well with mine. I have a round banister top, rectangular bottom. There are adapters for round posts. I needed a kidco extension for the gate at the bottom of my stairs, and this apparatus also extends out at least a few inches, just make sure you measure and check if you need an extension too

Q:could someone share installation instructions
A:
There should be some that come in the package. If not, I would call Amazon or the manufacturer.

Q:Would this work if the banister is round on top and bottom? my banister is like 3 inch round on both top and bottom.
A:
Yes. It comes with adapters

Q:How wide is this item?
A:
5″ inches wide

Q:Will I have to make any holes in the floor or banister itself? I am renting and not sure if the landlord would want the holes. Thanks.
A:
Hi Jazz. No drilling into the floor or bannister is required to put the gate up. There are pieces of wood included in the kit that mount inside the plastic white bracket, and you just drill into those.

Note: I did have to buy a longer bole and a coupler because my stairwell was 1″ too wide, but that isn’t normal, so you should be okay.