Richell Wood One-Touch Pet Gate, Autumn Matte Finish features

• Adjustable pet gate with security latch for safely confining pets
• Made of polished wood and metal; simple pressure-mounted installation
• Lock button and door stopper hold door firmly in place
• Door easily locks/unlocks with 1 hand; rubber stoppers prevent scratches
• Measures 2 by 28.3 to 35.8 by 34.6 inches

Wood One-Touch Pet Gate, Autumn Matte Finish

Q:i have a door frame that is under 29″ will this condense down to that size?

A:

It should be no problem. It’s instructions rea: “* Fits doorway or hallway openings from 28.3″ to 35.8″ wide
* Tension-mount design keeps gate permanently in place ”
I would note that we loved it and used it to the entrance to kitchen. HOWEVER, house guests tripped over the threshold a little. But there is no other way it could work without that bar.

Q:My door is 34″ will this fit? or is it specific size only?

A:

It can be adjusted…yes, it will fit

Q:Would this gate work with an opening of 41.5 inches? Do I need to purchase an additional optional frame extender to make it work? Thank you!

A:

Our doorway opening is 42 inches. We were able to make it work. We do have a bar space on both sides that is more like 2 inches. Depending on what type of animal you are trying to contain would really determine your answer. We use it for a bunny and its fine.

Q:I have a 40 inch wide door will this fit it

A:

Using the included extenders, yes.

Q:Can this be mounted between a wall and a door frame?-The left side would have to attach to drywall and the other to the side of a door frame.

A:

Not sure what you mean by “mounted”. It can be held in place between any two immovable sides (wall/door frame/etc) that are at least as tall as the gate. Pressure holds it into place – you basically turn the round adjusting knobs that have large screws passing through them (at the top and bottom of each side of the gate), and the pressure is increased or decreased – to tighten the gate into place, or loosen it to move it. Slats can be added to or removed from the side panels to increase or decrease the width. We have 1 of ours situated in a doorway, and the second is across a…
»
Read More

Not sure what you mean by “mounted”. It can be held in place between any two immovable sides (wall/door frame/etc) that are at least as tall as the gate. Pressure holds it into place – you basically turn the round adjusting knobs that have large screws passing through them (at the top and bottom of each side of the gate), and the pressure is increased or decreased – to tighten the gate into place, or loosen it to move it. Slats can be added to or removed from the side panels to increase or decrease the width. We have 1 of ours situated in a doorway, and the second is across a hallway (drywall to drywall). Hope this helps.
«

Show Less

Q:How wide is the opened gate walk through portion?

A:

The walk through portion is 18 inches…

Q:Wll this fit a 40 inch door frame

A:

I think you will need to purchase at least one extension.

Q:I am not sure if I should buy this one touch gate or the small free standing gate. The latter could be moved easily to block different rooms .

A:

Easy to use. I love it

Q:Our baseboard is tapered as it goes up. Will this create a problem with the lower tension mounts?

A:

You should not have a problem it’s adjustanle on 4 spots 2 on each side

Q:is the gate weather resistant I would like to use It on top of my deck steps?

A:

I doubt it. I expect the wood might warp, and the metal parts would rust. I’d stick to indoors.

 

Q:Will this withstand my 38lb dog jumping up and putting her paws on the top of the gate?

A:

I think that it appears to be sturdy enough. It’s just that the dog could possibly knock the handle that latches the gate hard enough and at the right angle that it would open.

Q:How does this gate work with small dogs? I have a 6 pound yorkie/maltese dog that has figured out how to wiggle her way through our current gate.

A:

I have a 5pound and 10 pound Maltese and never had a problem.I have had 3 pound foster puppies and it contained them also.

Q:Could anyone tell me how far part is the widest bar spacing? My dog is 6 pounds and her head is about 3″ wide.

A:

The spacing on the gate is 1 1/2″, the spacing on the 2 sides is variable and depends on the width of your doorway. We have ours set up in a 34″ doorway and on one side there is one 2 1/2″ space between the bars and on the other side one 2 1/4″ space.

Q:how tall is the gate to the top of the lift handle ( tallest part ) would it fit under a 35″ tall door knob ?

A:

Yes…the very tallest part of the knob and release button is 34 1/2 inches high when the handle is closed. When you lift the handle, it is almost exactly 35 inches at the tallest point.

Q:How difficult is it to remove and put up the gate? Is it something that can be done quickly?

A:

It takes a few minutes. You line up the gate in the doorway and then tighten the “screws” in the corners to pressure fit in the opening. Not something I’d want to do daily but certainly if you want to remove for company once in a while it is easy enough.

Q:My doorway is 28-5/16W. Would this one fit?

A:

Yes, it will. My doorways are under 30″ and this unit can go smaller or much larger. I have one and bought my son one and they’re simply the best. Hope this helps…

Q:HOw tall is this gate? I just noticed they have Extra Talls – the one I ordered for my big room is 38″ hi

A:

The one I have is 32″ from bottom of metal frame to top of curve. Works good for our dog and grandchildren.

Q:Do I need to buy frame extenders if my door frame is 35″?

A:

No I have mine stretched to 38″ but the further you stretch it the less stabile it is. My dog is 40 lbs and jumps on it but hasn’t knocked it down yet. I think 35″ would be stable and secure.

Q:What is the max width for this gate with added optional frame extenders?

A:

35.8″. see the user image of the instruction sheet: http://www.amazon.com/gp/customer-media/permalink/moI4HXO8C2Y7OV/B0006GW0YC/ref=cm_ciu_images_pl_link

Q:What is the width of the gate?

A:

It is 36 5/8″.